First Use with an Independent Displaying Device

NOTICE

notice

When starting the device for the first time and after every software update, you need to confirm the general terms and conditions (GTC) of the Hella Gutmann Solutions GmbH. Otherwise, certain device functions will be unavailable.

Proceed as follows to take the mega macs X into operation for the first time with an independent displaying device:

NOTICE

notice

In this video, you will learn how to connect the mega macs X to different display devices. You can watch the video here:

  1. Switch on the mega macs X.
  2. Switch on the independent displaying device (e.g. tablet or notebook).
  3. Wait until the Wi-Fi indicator at the mega macs X is permanently green.
  5. Establish the Wi-Fi connection (with QR code or manually) and call up the SDI diagnostic interface.
  6. The two connecting possibilities are described below:

Establish the Wi-Fi connection and call up the SDI diagnostic interface – with QR code:

  1. Scan the QR code on the housing of the mega macs X.
  3. The Wi-Fi settings are indicated on the displaying device.
  4. Confirm the indicated selection and connect with the mega macs X Wi-Fi.
  5. Now the mega macs X is connected with the displaying device.
  6. Scan the following QR code once to open the SDI diagnostic interface in a web browser:

  8. NOTICE

    notice

    It is recommended to use Google Chrome with version 78 or higher in connection with either Android or Windows operating system.

    The latest version of Safari web browser is presumed when using iOS.

  9. The web page http://macsx is going to be called up automatically.
  10. The SDI setup will start automatically in the next step to activate the mega macs X.
  11. Select the Wi-Fi network (of the workshop).
  12. The LED progress bar flashes during connection setup.
  13. Once the Wi-Fi connection is established, the message Wi-Fi connection has been successfully established is displayed.
  14. Select >OK<.
  15. Select >Continue<.
  16. Please enter the activation code and select >Continue<.

  17. NOTICE

    notice

    The activation code is going to be sent by e-mail in advance.

  18. Confirm the successful activation of the mega macs X with >Continue<.
  19. Enter the company data and confirm with >Continue<.
  20. Add a printer.
  21. Call up the SDI diagnostic interface with .

  22. NOTICE

    notice

    The following cases require a prior license activation to be able to use requested functions of the mega macs X:

    - Purchased device (cash purchase)

    - Flexible leasing

    If you need to activate licenses, please contact your sales partner.

  23. NOTICE

    notice

    It is recommended to add a shortcut of the mega macs X setup on the start screen once. Hence you do not need to manually enter the address http://macsx (http://macsx.local or http://192.168.4.1 in the browser every time you set up the connection to the mega macs X.

    Perform the steps as described in section Creating a Shortcut to add the setup of the mega macs X to the start screen.

  1. After having completed the installation process you can start the mega macs X through the shortcut on the start screen.

Establish the Wi-Fi connection and call up the SDI diagnostic interface – manually:

  1. Start a manual search for Wi-Fi through the displaying device.
  2. Select the SSID macsx** (** marks the device number).
  3. Enter the Wi-Fi password (key) and connect to Wi-Fi.

  5. NOTICE

    notice

    The Wi-Fi password (key) is additionally written on the type label at the back of the mega macs X.

  6. Open the web browser and enter the following address in the address bar: http://macsx.

  7. NOTICE

    notice

    Should you use a displaying device with Windows operating system, then enter the address http://macsx.local or http://192.168.4.1 in the address bar.

    Connection cannot be established if http:// is not entered.

  8. The SDI setup will start automatically in the next step to activate the mega macs X.
  9. Select the Wi-Fi network.
  10. Regard the window with information and instructions.
  11. The LED progress bar flashes during connection setup.
  12. Once the Wi-Fi connection is established, the message Wi-Fi connection has been successfully established is displayed.
  13. Select >OK<.
  14. Select >Continue<.
  15. Please enter the activation code and select >Continue<.

  16. NOTICE

    notice

    The activation code is going to be sent by e-mail in advance.

  17. Confirm the successful activation of the mega macs X with >Continue<.
  18. Enter the company data and confirm with >Continue<.
  19. Add a printer.
  20. Confirm your selection with >Continue<.
  21. Call up the SDI diagnostic interface with .

  22. NOTICE

    notice

    The following cases require a prior license activation to be able to use requested functions of the mega macs X:

    - Purchased device (cash purchase)

    - Flexible leasing

    If you need to activate licenses, please contact your sales partner.

  23. NOTICE

    notice

    It is recommended to add a shortcut of the mega macs X setup on the start screen once. Hence you do not need to manually enter the address http://macsx (http://macsx.local or http://192.168.4.1 in the browser every time you set up the connection to the mega macs X.

    Perform the steps as described in section Creating a Shortcut to add the setup of the mega macs X to the start screen.

  1. After having completed the installation process you can start the mega macs X through the shortcut on the start screen.